Metal Chimney Repair in Galloway means fixing rusted steel stacks, failed stainless liners, and leaking flashing before they rot your roof deck. We handle factory-built and steel chimneys across Galloway Township, Smithville, and Pomona. If your stack is streaking rust or your liner is pitted, we diagnose it and fix it, usually same day.
Metal Chimney Repair in Galloway is the specialized trade of restoring factory-built and steel chimney systems rather than masonry stacks. We pull the chimney cap, run an inspection camera down the flue, and check the stainless steel liner for pitting, cracked seams, and separated joints. Then we repair or replace the damaged section, reseal the storm collar, and re-flash the penetration. Most steel chimneys fail at the joints and the cap, not the middle of the pipe.
Galloway sits close enough to the coast that salt air eats galvanized steel faster than inland towns see. Add our freeze-thaw swings and you get rust jacking, spalling at the chase, and water tracking down the pipe into the ceiling. If you have been searching for metal chimney repair near me in Galloway, the fix is usually a stainless steel liner upgrade, new flashing, and a proper cap. We quote steel chimney repair cost Galloway New Jersey upfront before we start.
Every job starts with a camera inspection and a written scope, so you know exactly what is being fixed and why. The inclusions below cover the standard repair. A full reline or a chase rebuild is quoted separately because the materials and labor are different.
We run an inspection camera the full length of the flue and check for pitting, seam separation, and creosote. You see the footage and the photos before we quote anything.
We inspect the chimney cap, storm collar, and roof flashing, since that is where most leaks start. Failed sealant gets cut out and replaced, not caulked over.
Pitted pipe sections get cut out with an angle grinder and replaced with matching stainless. Localized liner damage gets patched; a compromised full run gets a new stainless steel liner.
Every joint we touch gets high-temp sealant rated for the flue temperature. That is what stops the smoke smell and the water tracking that corrodes the pipe from the outside in.
We fire the appliance, verify draft, and check the damper and damper clamp. If smoke spills or the damper sticks, we fix it before we call the job done.
Drop cloths down, old pipe hauled away, and a walkthrough of what we replaced. You get maintenance guidance and a reminder for the next annual inspection.
You call (844) 803-5147 and describe what you are seeing: rust streaks, water stains, smoke rolling back, or a cap that blew off in a storm. We ask about the appliance, the pipe brand if you know it, and how long the issue has been going on. That call usually tells us whether this is a same-day fix or a scheduled reline.
We get on the roof, pull the chimney cap, and run an inspection camera down the flue. We check the stainless steel liner for pitting and seam separation, inspect the flashing and storm collar, and look at the chase for spalling. You get photos and a straight answer on what failed and why. Takes about 45 minutes.
Before any work starts, you get a written scope with the price on it. If it is a section replacement, we list the pipe, the cap, and the flashing separately. If it is a full reline, we quote the stainless steel liner length and the insulation wrap. No add-ons after the fact.
We cut out the failed section with an angle grinder, fit the replacement pipe, and seal the joints with high-temp sealant rated for the flue temperature. New flashing goes in at the roof penetration, and the cap gets re-pitched or replaced. Most jobs run two to four hours. We keep drop cloths down and haul away the old pipe.
We fire the appliance, check draft, and confirm no smoke spills at the joints. You get a walkthrough of what we replaced, how to spot early rust, and when to schedule the next inspection. Our workmanship is warrantied, and we leave the roof and the hearth cleaner than we found them.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Runs the full length of the flue to find pitting, seam separation, and creosote without guessing from the roof.
Cuts out failed pipe sections cleanly so the replacement fits flush and seals properly at the joint.
Sweeps creosote from wood-burning flues before any liner work, so the new surface stays clean.
Repacks mortar joints on the chase when water has been getting behind the brick and rusting the pipe.
Removes failed flashing and old sealant at the roof penetration so the new flashing seats correctly.
Fitted where code requires it, keeping the damper from fully closing on a gas log set.
A 1998 factory-built steel chimney had rust streaks down the chase and water staining the ceiling below. The storm collar had failed and water was tracking behind the pipe. The homeowner had been quoted a full replacement.
We replaced two pitted pipe sections, rebuilt the flashing and storm collar, and fitted a new cap. Total cost was $520 instead of the $3,400 replacement quote. Draft tested clean and the ceiling stain stopped spreading.
A homeowner's wood stove smoked into the room every time they lit it. The existing liner was pitted and undersized for the appliance, so draft could not establish. They had stopped using the fireplace entirely.
We relined the flue with a correctly sized stainless steel liner, insulated it, and replaced the cap. Draft tested within spec and the stove lights clean. The reline ran $2,600 and the fireplace is back in use.
A nor'easter tore the cap off a metal chimney and rain poured straight down the flue into the firebox. The homeowner called at 8 a.m. with water already on the hearth.
A tech was on the roof by early afternoon with a temporary cap. We returned four days later with the permanent cap and new flashing. Total was $410 and there was no water damage to the ceiling or firebox.
Steel chimneys fail in predictable places, and Galloway's salt air and freeze-thaw swings speed all of them up. Here is what we see most and how we handle it.
Ask a pro →We pull the cap, inspect the collar and flashing, and rebuild the penetration with new flashing and waterproofing sealant. If the pipe itself is pitted, we cut out the bad section and replace it with matching stainless.
We camera the flue, measure the liner, and reline it to the correct diameter for the appliance. Then we test draft with the appliance running and confirm the damper is sealing properly.
We fit a new cap sized to the flue, with a screen where code requires one, and secure it against the wind loads we get on this side of the state. Most cap replacements are done in under two hours.
We free, repair, or replace the damper and fit a damper clamp where code calls for one. Then we verify the fireplace drafts correctly with the damper in both positions.
Most repairs run $180-$450 for a section fix, $250-$600 for cap and flashing work, and $1,800-$4,500 for a full stainless reline. Typical 2026 pricing in this area depends on pipe diameter, roof pitch, and how much of the liner is pitted. We quote the price in writing before we start, so the number you hear on the phone is the number on the invoice.
We do. Thrive Sharp handles steel chimney repair Galloway NJ homeowners need, including Selkirk, DuraVent, and Olympia Chimney factory-built systems. Call (844) 803-5147 and we will schedule an inspection, usually within a day or two, and often same-day if water is actively coming in. Our technicians are CSIA-trained and work to NFPA 211 clearances.
Yes, and most can be repaired rather than replaced. Pitted sections get cut out and replaced, failed caps get re-pitched or swapped, and flashing gets rebuilt at the roof penetration. A full reline with a stainless steel liner is the fix when the whole flue is compromised. We confirm which path you need after the inspection camera run, not before.
Salt air, freeze-thaw cycles, and water at the joints are the big three. Coastal humidity corrodes galvanized steel, winter swings crack sealant and open seams, and a failed storm collar lets water track down the pipe. Creosote buildup in wood-burning flues adds another failure point. We check all of it during the inspection and show you the photos.
Chimney Repair Near MeGeneral chimney repair for masonry and steel stacks across Galloway. If your issue turns out to be mortar or brick rather than the metal pipe, this is the service that covers it, and we handle both on the same visit.Explore →
Chimney Masonry RepairWhen the chase around your steel chimney has spalling brick or crumbling mortar, masonry repair restores the surround. We match the mortar and re-point the joints so the chase stops letting water reach the pipe.Explore →
Chimney Crown RepairA cracked crown dumps water straight into the chase. We rebuild the crown with chimney crown mix and pitch it away from the flue, which protects the metal pipe below from the top down.Explore →
Chimney ReliningFull stainless steel liner installation for flues that are too far gone to patch. We size the liner to the appliance, insulate it, and connect it to the cap and the appliance collar.Explore →
Chimney Cap RepairCaps take the worst of the wind and salt. We re-pitch, re-secure, or replace damaged caps, and add a spark arrestor screen where the appliance calls for one.Explore →
Chimney MaintenanceAnnual inspection and sweeping keep small rust spots from becoming liner failures. We check the cap, flashing, and liner every year and catch problems while they are still cheap to fix.Explore →
Fireplace RepairDamper malfunction, cracked firebrick, and smoke backdraft often trace back to the chimney, not the firebox. We fix the fireplace and the flue together so the whole system drafts correctly.Explore →
Emergency Chimney RepairStorm damage, a cap blown off, or water pouring in during a nor'easter. We tarp, cap, and stabilize the same day, then schedule the permanent repair.Explore →Rust streaks, a missing cap, or water in the flue, we diagnose it and fix it. Licensed, insured, and warrantied, with upfront pricing before we start. Call (844) 803-5147 and we will get a tech on your roof.
Book an Inspection (844) 803-5147 →Call (844) 803-5147 or send us a message and we will get back to you the same business day. We book Monday through Friday, 8 a.m. to 6 p.m., with same-day and after-hours slots for active leaks and storm damage. Tell us what you are seeing and we will tell you what it takes to fix it.